* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
It is used by the gorilla (12V). It equipped with back-step-izing. Having meat-omission-processed it, he is smart. Moreover, compared with other products, it is thick, and in the weak MONGORI system of a crankcase, if good for the oscillating m
It is used by the gorilla (12V). It equipped with back-step-izing. Having meat-omission-processed it, he is smart. Moreover, compared with other products, it is thick, and in the weak MONGORI system of a crankcase, if good for the oscillating measure ? reinforcement ? of a case, I will consider. YO which is recommended.
As expected of GCraft, the accuracy is fine and the STAND fits without any interference. You can adjust the stand holder to avoid hitting the swing arm when you raise the stand, which is a common problem with modified monkeys.View Detail
I installed it when MONKEY's Rear Sets were installed. However, my MONKEY is LowdownSpec. For Short Side Stand I was too standing for this product could not be used. But, making small details etc etc etc. There is no complaint. If I have the opportunity to use it for the next vehicle production I would like to use it.View Detail
Because many of the related parts of xr motard have been discontinued, so there are not many related products to choose from, but relatively speaking, I think it is relatively expensiveView Detail
I have searched for a lot of related products, most of which are only silver, only g-craft has the black color I want, but the parts of this brand are relatively expensiveView Detail
As expected of GCraft, the accuracy is fine and the STAND fits without any interference. You can adjust the stand holder to avoid hitting the swing arm when you raise the stand, which is a common problem with modified monkeys.View Detail
Previously on & omega; It's too good to throw away, so do-it-yourself measures
The rattling thing is a recessed OEMSTAND 12.4mm wide. This one is 12.5mm wide. So we ordered Stainless Shim inner diameter 12mm, outer diameter 22mm, and thickness 0.1mm.
Bite into this stuff and it's perfect. I ordered 0.05mm, 0.02mm and 0.01mm just to be sure, but they're out of stock & omega; Also, you should definitely have a spring hook. Even a cheap one is enough for me, so I'll keep it & omega; It's a full-powered tool and I'm afraid of substitutions. STANDBolt/Nut is 14mm/14mm Side stands sensor fixed bolt is 8mm
Too short All Screw, Order M12/P1.75 inch cut Stainless bolt 110mm for extension The Uniqlo length NutM12/L60 on this one. I couldn't find a good one around L60 in Stainless Steel length Nut, so I used Uniqlo ω Also, the M12Stainless Nut 3 different thin 1Pack The rest of it will be on the rubber board for about 1,000 years. It's a useless cost, but it's unavoidable.
I decided to temporarily connect them with a long nut for 30mm each, and then fill up the all screw of the body with 30-35mm
I used a disk grinder to cut it down to 32mm. It's adjustable, so just use About.
Then, put two nuts in the bolt for the double nut, put the body cut with a long nut and tighten it up.
Also, the angle of the STAND toe is poor, and it's only grounded on the inside of the STAND only. So I put it on the Rubber Board Teketo and it's done
Well, I've managed the Large goal of somehow improving my over-sleeping OEMSide Stand. I'm not happy with some of the details, but it's good because we achieved the minimum objective.
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING