* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
What made you decide to buy? I was concerned about the fading of the top side of the OEM Handlebar Clamp
Was it difficult to install? What is the point or hang of the installation? Just remove the Clamp's M8×35mm Bolt and replace it I was going to reuse the Bolt, but I couldn't forgive the collaboration between our shiny product and the faded state of the Bolt There was none, so I replaced it with Stainless's Bolts with Flange
How was your experience with it? If you click on the product name "Stabilizer" in the image, you can see the Front Fork Image Stabilizer-like anti-sway, but with a Handlebar As for the Stabilizer, I think it is almost the same as OEM I think it became quality improvement around the Handlebar from the riding posture Moreover, there was a sense of unity because the handlebar is also ZETA
Was the Instruction Manual easy to understand? Parts:Were you following? Included Parts:none, except for the actual item
[Was there anything that disappointed you? Faded Top Burridge and glossy looking Gap of the current one when viewed from the side
Do you have any wishes or improvements you would like to make for the Manufacturer? It was noticed after purchase, but the SX and COMP of the advertising photo have the shape (Mounting Bolt) It seemed to be different... SX's is more of a hexagonal head bolt that does not protrude (the bolt head sinks in) I wanted to make the shape of SX for COMP as well
[Do you have any products to compare it to? ZETA Handlebar clamp kit
I'm embarrassed to say that I first learned about this item at my local RecycleMotorcyclePartsShop just a few days ago. It is the type that adjusts the position with the old type Edge that is easy to adjust the handle position, which I saw in your impressions. The stiffness is certainly improved slightly. Since the position can be aligned properly, after disassembling the front end, it can be assembled more quickly than ever before.View Detail
For the time being, it feels expensive and Handlebar matching marks are only on the surface, so it is hard to match. So, one star drop.
I wrote the title as rigidity Up, but ... 1 Since it is made into Piece, I think that its structural rigidity is rising. However, something does not change for running (I can not feel it) is. Can you feel it to those who can attack violently?
I think that there is no problem even if it remains as an OEM, but even if you do not feel the efficacy, there is still a sense of security. I bought it cheaply using Point and it arrived, but if I did not have a point, I might not have bought it for a while.
Although it looks pretty good, if you attach the Bar pad, it disappears (Lol). Installation is 2 pcs. I feel more comfortable.
Anyway, I think that I'm glad I bought it.View Detail
Also attached here as well as Handlebar exchange. I feel like it looks good and rigidity has improved. I do not know. (Lol) It is not a very high part, but I installed it with full emphasis on appearance. Although it is blocked by the Bar pad, it does not look. wView Detail
The touch which the rigid feeling became very high and in which handle operation also became brave carries out this Handle clamp by clamping with one piece rather than clamping with two piece, as it is written also on explanation.The music of the Handle by the fall also decreases. Isn't it less expensive than expected as a result?The Design can also be made quite smart and becomes a recommended excellent piece also as a Dress-up parts.Although I am using also for the Enduro race, I think that it is very good.View Detail
After I have changed my handle bar to 28mm, I decided to search for a bar clamp that would look better and solid. I have to make sure the mounting pitch is correct. The product number -3096 represents 96mm.View Detail
I'm using it on my 2007 WR250X with the Y's Gear OEM Taper BarClamp set.
I hesitated whether to put on the Bar pad of yz250fOEM or to use SXStabilizer, but I chose SXStabilizer because it is easier to adjust the position than Memory of Upper clamp of OEM. However, I chose SXStabilizer because it is easier to adjust the position than the OEM upper clamp memory, and also I chose the design and moderate stiffness up.View Detail
I'm embarrassed to say that I first learned about this item at my local RecycleMotorcyclePartsShop just a few days ago. It is the type that adjusts the position with the old type Edge that is easy to adjust the handle position, which I saw in your impressions. The stiffness is certainly improved slightly. Since the position can be aligned properly, after disassembling the front end, it can be assembled more quickly than ever before.View Detail
For the time being, it feels expensive and Handlebar matching marks are only on the surface, so it is hard to match. So, one star drop.
I wrote the title as rigidity Up, but ... 1 Since it is made into Piece, I think that its structural rigidity is rising. However, something does not change for running (I can not feel it) is. Can you feel it to those who can attack violently?
I think that there is no problem even if it remains as an OEM, but even if you do not feel the efficacy, there is still a sense of security. I bought it cheaply using Point and it arrived, but if I did not have a point, I might not have bought it for a while.
Although it looks pretty good, if you attach the Bar pad, it disappears (Lol). Installation is 2 pcs. I feel more comfortable.
Anyway, I think that I'm glad I bought it.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING