[Rozmiar]
szerokość : Około 760 mm
Długość : Około 500 mm
Wysokość : Około 520 mm
[Materiał]
FRP
Zawartość produktu
Korpus osłony, zestaw uchwytów, ekran, zestaw śrub ekranowych
*Osłonka ta jest produktem ogólnego przeznaczenia wykonywanym za granicą, więc mogą wystąpić zadrapania, zadrapania, otarcia itp. które mogą spowodować, że otwory nie będą pasować i może zaistnieć konieczność ich modyfikacji w celu instalacji. Przed dokonaniem zakupu należy zapoznać się z poniższymi informacjami.
*Zespół oświetleniowy i osłona mogą się wzajemnie zakłócać, w takim przypadku należy usunąć zakłócającą część osłony.
*Widelec i osłona mogą przeszkadzać sobie nawzajem, dlatego należy sprawdzić zakres ruchu lewej i prawej strony i ogolić osłonę w przypadku wystąpienia zakłóceń.
*Inne zakłócające elementy muszą być cięte, golone lub przetwarzane w inny sposób.
*W przypadku jednostek oświetleniowych sprzedawanych oddzielnie, uprząż przedłużająca z uprzęży głównej musi być wykonana.
*Otwór pomiędzy nożycami a osłoną może się przesuwać w zależności od położenia osłony. W tym przypadku trzeba poszerzyć otwór w osłonie.
*Istnieją przypadki, w których otwory na ekranie i w osłonie nie pasują do siebie, w tym przypadku należy przymocować ekran i otwory w osłonie od centralnego otworu osłony na zewnątrz za pomocą nakrętki studni, a następnie poszerzyć części, które nie pasują do pilnika.
*Niektóre partie nie mają otworu po stronie osłony na ekran. W takim przypadku należy wywiercić otwory, aby dopasować je do ekranu.
*Metody obróbki inne niż te wymienione tutaj nie są dostępne, dlatego należy sprawdzić w rzeczywistym pojeździe.
*Produkt jest poddawany obróbce, dlatego nie możemy przyjmować zwrotów za brak możliwości jego instalacji.
*Przed malowaniem proszę upewnić się, że produkt został przetworzony i zainstalowany. Po pomalowaniu nie będą przyjmowane żadne roszczenia.
*Należy pamiętać, że specyfikacje produktu mogą ulec zmianie z przyczyn podanych przez producenta.
[Size]
Width: Approx. 760mm
Front and rear length: Approx. 500mm
Height: Approx. 520mm
[Material]
FRP
Components
Cowl body, bracket set, windshield, windshield screw set
*Please make sure to read the notes before purchasing.
*7 inch projector LED headlight unit and the same type of light unit are used for the lights.
*Because this cowl is a universal product made non Japanese, it may have some scratches and scuffs, and the holes may not fit, so some modification is required for installation.Please make sure you understand the following information before purchasing.
*The light unit and cowl may interfere with each other, in which case it is necessary to shave the interfering part of the cowl.
*There is a case that the fork and the cowl interfere with each other, check the range of movement of both sides and if it interferes, it is necessary to shave the cowl.
*Other interfering parts need to be cut or shaved.
*For light units sold separately, it is necessary to make an extension harness from the main harness.
*Depending on the positioning of the cowl, the hole between the bracket and the cowl may be misaligned.To do this, you will need to widen the hole in the cowl.
*In some cases, the holes of the windshield and the cowl do not match, in that case, you need to fix the windshield with the well nut from the center hole of the cowl to the outside, and widen the holes with a file in order.
*Depending on the lot, some of them do not have the hole for the windshield on the cowl side.In this case, please drill the holes in order to match the windshield.
We will not provide information about processing methods other than those mentioned here, so please verify according to your actual bike.
*Any returns will not be accepted due to inability to install the product.
*Please be sure to process and install before painting.Any claims after painting are not accepted.
*There may be changes in product specifications due to the manufacturer's reasons.