Materiał: stal
[Rozmiar]
· Od dołu do wałka osi: około 460 mm (StockSize) , Około 510 mm (2-inchesOver)
· Szerokość: ok. 212mm
[Zawartość]
·Ciało
· Najlepsza herbata
·Pion
· Spacer na kierownicę
· Panel hamulcowy
·Wał
· Wheel CollarXQuantity: 1 zestaw
* Panel hamulcowy zostanie wysłany oryginalnie, zostanie wymieniony na oryginalne towary przetworzone.
[O łożysku]
* -1 Łożyska wrzecionowe JR - 341851 są używane do pojazdów z łożyskiem kulkowym różanym lub z łożyskami kulkowymi różowymi, proszę użyć zestawu 74 Springer Fork dla łożysk kulkowych G5-00292 i G5 - 00293 róż.
* Łożyska prawdziwej adopcji zmienią się w 99 roku powyższego numeru nadwozia. Również w roku adaptacji, ponieważ jest często zastępowane łożyskiem kątowym tego ostatniego typu w konserwacji, należy potwierdzić, że zostanie ono potwierdzone przed demontażem jest polecany.
* Górny bieg łożysk tego produktu będzie wyłącznym przedmiotem poddanym obróbce tokarskiej zgodnie z wałem trzpienia.
* Dołączone łożysko kątowe to zestaw górnego i dolnego wyścigu oraz łożyska. W przypadku wymiany łożyska dolnego należy użyć oryginalnego.
[Należy pamiętać o hamulcach]
Widelec Springera jest znacznie niższy niż widelec teleskopowy, który jest obecnie prawie całkowicie zaadoptowany.
W przeciwieństwie do zwykłych hamulców, operuj hamowaniem o około 30% z przodu i około 70% z tyłu.
Ten produkt będzie przedni widelec konstrukcji około 80 lat temu. Droga i sytuacja na drodze również różnią się znacznie od czasu. Uczucie działania również zmienia się bardzo, więc dopóki nie przyzwyczaisz się do operacji w wystarczającym stopniu (Oczywiście, nawet po tym) Zachowaj bezpieczną jazdę.
[O instalacji]
Pamiętaj, aby poprosić o specjalny sklep do instalacji tego produktu.
Osoby wykonujące pracę powinny uważnie przeczytać instrukcję montażu i wykonać pracę.
* Zapomnienie o przyczepieniu smaru, blokadę śrubową itp. ma możliwość spowodowania poważnego wypadku.
Nie gwarantujemy żadnych problemów z powodu nieprzestrzegania środków ostrożności.
[O zużyciu łożysk]
Widelec Springera jest znacznie cięższy od normalnego widelca teleskopowego, skok widelca jest niewielki, tłumik nie tłumi, więc ból łożyska będzie szybszy.
Wymień go na rozpiętość wcześniejszą niż instrukcja obsługi i często smaruj go często.
Material: Steel
[Size]
・From the bottom of the under-stem to the axle shaft: Approx. 460mm (stock size), 510mm (2 inches over)
・Width: Approx. 212mm
[Components]
・Body
・Top T
・Riser
・Handlebar spacer
・Brake panel
・Shaft
・Wheel collar x 1 set
*Please send us the stock brake panel and it will be replaced with the stock one.
[about the bearings]
*-Please use the 74 springer fork kit for G5-00292 and G5-00293 ball bearings if if the vehicles are equipped with 1JR-341851 stem bearings or with ball bearings in pieces.
*Bearings used in stock are different between 99 and older models of the above VIN.It is recommended that you disassemble and check the bearings first, since they are often replaced with later angular bearings during maintenance even for the adapted model year.
*The upper bearing race of this product is a special product that is lathed to fit the stem shaft.
*The angular bearing included is a set of upper and lower race + bearing.If the lower bearing is also replaced, please use the stock bearing.
[Note on brakes]
Springer forks are significantly less strong than the telescopic forks that are currently used on almost all stock vehicles.
In contrast to stock braking, please ride with about 30% front and 70% rear braking.
This product is a front fork of about 80 years old structure.The road and traffic conditions are very different from those days.Please drive safely until you get used to the operation of the vehicle (and after that, of course).
[About the installation]
Please ask a professional shop to install this product.
Please read the assembly instructions carefully before starting work.
*If you forget to put grease or screw lock, it may cause a serious accident.
Any problems caused by the failure to follow the precautions are not guaranteed.
[About bearing wear and tear]
Springer forks are much heavier than stock telescopic forks and have less stroke and no damper damping, so the stem bearings get damaged faster.
It is recommended that the grease be replaced earlier than specified in the manual and that the grease be replaced frequently.